Then Dry fit and finally use the silicon when attaching the CableClam to the box.
You want to make a small slit in the black membrane of the CableClam for the wire to pass through. But, this time we will be using the CableClam for the wire. It will be the same process of choosing a bit slightly larger and drilling the hole. Next we will move on to the actual wire for the fish finder. just make sure to try and clean up any mess before it dries! You can run a couple beads around the inside if you would like as well. Also, use the silicon on the threads of the screws when you screw them in. first dry fit to make sure everything is correct, then once you are satisfied make sure to use a generous amount of silicon on the back plate and around the edges to ensure a tight seal. it is time to insert the 12v chargers into the holes you drilled. After you have drilled out the holes that are need for the charger area make sure smooth over the edges with a utility knife or even sand paper if you have it. It is very important that we keep the box as watertight as possible, we do no want any of the wires or battery to get wet. you want to make sure that the holes are only slightly larger so that way we have less area to seal up with the silicon. We will begin by choosing a drill bit that is slightly larger than the ports of of the 12v plugs. So this is where we start to make the overall projects. You DO NOT need this part if you only want to power your fish finder!ħ) Insulated electrical connectors, the sizing of these depend on the size of your wire, battery connectors and charger connectors.Ĩ) A set of Alligator Clips I chose red and black to keep the connections easy to see.ĩ) Lastly, some silicon marine grade sealant. I chose this so that I can also hook up a phone charger or anything else that will plug into a USB or cigarette lighter outlet. I went with a Sealed Lead Acid Battery Charger UPG D1724ĥ) A Blue Sea Systems CableClam, this will be for the fish finder cord to pass through the box and connect to the battery.Ħ) A Electop Dual USB Socket Charger 2.1A & 2.1A with LED + 12V Power Outlet Cigarette Lighter Socket, Triple Function Panel for Car Marine Vehicle Motorcycle ATV. The blue stuff around the battery is just a foam knee pad i put around to make it a snug fit in the box.Ĥ) You will also need a way to charge this battery. The one I chose to use was CB CHROMEBATTERY 12V 7AH Sealed Lead Acid (SLA) Battery Piranha MAX 160 Fish Finder. I chose the Plano 131252 Dry Storage Emergency Marine Box, Orangeģ) A power source. I have the Garmin Striker 4Ģ) A Dry Storage box too house the battery. I will include images for all the parts you will need!ġ) You will need your fish finder. Using other aftermarket connectors or splicing other connectors into the YP system may cause damage to the system or the accessories connected to the system and may void your warranty.Ĭaution: Make sure to pay attention to the actual wire colors of all our accessory cables to ensure that the red (+) wire is always connecting to the red (+) wire on the connector into which it is being plugged.So this build doesn't really require too many things! While every fish finder is different I will be referencing the one I own for this build. Yak-Power uses our own custom tooled, high tolerance, very snug fitting connectors with larger gauge, real copper wire to ensure a quality, weatherproof and reliable connection.Īll our plug-and-play accessories are specifically designed to work together while maintaining the correct battery polarity throughout the entire Yak-Power system. Note: Make sure the plug-and-play connectors are completely pushed together when connecting the system together.
#Kayak battery box full
The Power Pack also comes with a home battery charger that maintains your batteries and ensures that you always have a full charge whenever you go out! The integrated external, dual USB charging port ensures that both your mobile device and outdoor action camera have all the power they need to capture all the action while you’re on the water. The compact and waterproof design can hold up to three 7AH batteries or two 12AH batteries while still being small enough to stow away in many hatches. The built-in master power switch gives you full control of when your power is on or off.
Our Power Pack Battery Box is the ultimate power solution for your kayak! It comes with an integrated Power Port outlet, which makes it easy to plug in and power your 12-volt accessories. 1A smart trickle battery charger included.Holds up to three (3) 7AH or two (2) 12AH batteries (not included).
Compact and waterproof design with configurable foam inserts.
0 kommentar(er)
